A Zener diode alone can hold a voltage steady, but it can only feed a few milliamps before it overheats. Add one transistor and the same Zener can regulate a whole 100 mA load. The trick is the emitter follower: the Zener sets a fixed voltage at the transistor's base, the transistor copies that voltage to its emitter (minus one diode drop), and the transistor — not the Zener — carries the load current. This article designs such a regulator step by step and works out how steady its output really is.
Figure 1: The Zener (a) sets the base voltage and the transistor carries the load current; the plot (b) shows the output holding at 4.9 V over a wide input range. (Schematic, not to scale.)
How it works — the Zener sets the base, the transistor does the work
In Figure 1(a), resistor R1 feeds current into a 5.6 V Zener diode, which holds the transistor's base at 5.6 V. The transistor is an emitter follower, so its emitter sits one base-emitter drop below the base:
Vout = VZ − VBE = 5.6 − 0.7 = 4.9 V
If the load tries to pull the output down, the base-emitter voltage rises, the transistor conducts harder, and the output is pulled back up. The Zener only has to supply the transistor's base current — a small fraction of the load current — while the transistor handles the full load.
Worked example — designing for a 100 mA load
Take an unregulated 12 V input and a 100 mA load (a 49 Ω resistor at 4.9 V). Use a TIP31 transistor with a current gain β of about 100. The base current is:
IB = IL / β = 100 mA / 100 = 1 mA
Design the Zener current at about 5 mA — enough to keep the Zener firmly in breakdown, small enough to waste little power. R1 must supply both currents:
R1 = (Vin − VZ) / (IZ + IB) = (12 − 5.6) / 6 mA = 1067 Ω
Use the standard value 1 kΩ. Check it: the current through R1 is (12 − 5.6) / 1000 = 6.4 mA, so the Zener gets 6.4 − 1 = 5.4 mA — right on target. The Zener dissipates only 5.6 × 5.4 mA = 30 mW, so even a small 400 mW Zener is comfortable.
Worked example — what if the input voltage wanders?
An unregulated 12 V supply is never exactly 12 V. Check the extremes with the same 1 kΩ resistor:
Vin = 10 V: IR1 = 4.4 mA, IZ = 3.4 mA — still regulating
Vin = 14 V: IR1 = 8.4 mA, IZ = 7.4 mA, Zener power 41 mW — still fine
Regulation holds as long as the Zener gets any current at all, which needs (Vin − 5.6) / 1 kΩ > 1 mA, or Vin above about 6.6 V. Below that the Zener starves and the output falls with the input, as Figure 1(b) shows. At the other end, the input must stay high enough to leave headroom across the transistor — with a 12 V input there is plenty.
Worked example — how steady is the output when the load changes?
When the load current changes, the base current changes, and the Zener current changes by the same amount in the opposite direction. A 5.6 V Zener has a dynamic resistance of about 10 Ω, so its voltage moves a little when its current moves. If the load jumps from 50 mA to 150 mA, the base current rises by 1 mA, the Zener current falls by 1 mA, and:
ΔVZ = 10 Ω × (−1 mA) = −10 mV
So the output moves by only about 10 mV for a 100 mA load change — an output resistance of roughly 0.1 Ω. A bare Zener feeding the same load directly would move hundreds of millivolts. The transistor divides the Zener's resistance by its current gain, which is the whole point of the circuit.
The same reasoning applies to ripple: 1 V of ripple on the input reaches the Zener only through the divider formed by R1 and the Zener's 10 Ω, so the output ripple is about 1 V × 10 / 1010 ≈ 10 mV — a hundredfold reduction.
Worked example — the transistor's heat
Nothing is free: the transistor drops the difference between input and output, and turns it into heat:
P = (Vin − Vout) × IL = (12 − 4.9) × 0.1 = 0.71 W
A TIP31 in a TO-220 package has a junction-to-ambient thermal resistance of about 62.5 °C/W without a heatsink, so its junction would rise by 0.71 × 62.5 = 44 °C, reaching about 69 °C in a 25 °C room — safe, but warm. Fit a small heatsink and the margin grows. This heat is the real limit of a series regulator: at higher currents or bigger input-output differences, a switching regulator is the better tool.
Key points to remember
- A Zener diode plus an emitter-follower transistor makes a series regulator: the Zener sets the base voltage, the transistor carries the load current, and Vout = VZ − VBE.
- Worked example: with a 5.6 V Zener, a 12 V input and a 100 mA load (β = 100), the base current is 1 mA and R1 = 1 kΩ gives a Zener current of 5.4 mA; the output is 4.9 V.
- Regulation holds while the Zener gets current — here for inputs from about 6.6 V up to 14 V, with the Zener dissipating only 19–41 mW.
- Worked example: a load change of 50 mA to 150 mA moves the output by only about 10 mV (output resistance ≈ 0.1 Ω), and 1 V of input ripple appears as only about 10 mV at the output.
- Worked example: the transistor dissipates (12 − 4.9) × 100 mA = 0.71 W and reaches about 69 °C without a heatsink — fit a small heatsink for margin.
- This simple regulator is ideal for small fixed supplies (a 5 V logic rail from a 12 V adapter), but for large currents or big voltage drops, a switching regulator wastes far less power as heat.
