Wien Bridge Oscillator: Build a 1 kHz Sine Wave with One Op-Amp

Author: Abloom Instruction Date: November 19, 2026

The RC phase-shift oscillator from an earlier article makes its sine wave by shifting the signal 180° through three RC sections. The Wien bridge oscillator takes a different route: a bridge of two resistors and two capacitors picks out one frequency, and the op-amp only has to provide a gain of exactly 3. It is the circuit inside many audio signal generators, and this article works out its frequency, its gain, and how to design one for 10 kHz.

Schematic of a Wien bridge oscillator with a series 16 kilo-ohm resistor and 10 nanofarad capacitor and a parallel 16 kilo-ohm resistor and 10 nanofarad capacitor feeding the non-inverting input of an op-amp with 10 and 20 kilo-ohm gain-setting resistors, beside a plot of the 995 hertz sine output of about 10 volts peak with a period of 1.01 milliseconds


Figure 1: A Wien bridge oscillator (a) — the series and parallel RC arms form the bridge that feeds the non-inverting input, and R1 = 10 kΩ with R2 = 20 kΩ sets the gain to 3. The output (b) is a 995 Hz sine of about 10 V peak, with a period of 1.01 ms. (Schematic, not to scale.)

Why it oscillates — the bridge and the gain of 3

The bridge has two arms. The series arm is a resistor and a capacitor in series; the parallel arm is the same resistor and capacitor in parallel. At one special frequency the bridge passes the signal from the output back to the non-inverting (+) input with no phase shift at all, but weakened to exactly one third of the output. The op-amp is wired as a non-inverting amplifier, which adds no phase shift either, so the signal going around the loop comes back exactly in phase — the Barkhausen condition for oscillation. For the loop gain to reach 1, the amplifier must multiply the signal by exactly 3, to undo the bridge's one-third attenuation. That is why R1 = 10 kΩ and R2 = 20 kΩ: the non-inverting gain is 1 + R2 / R1 = 1 + 20 / 10 = 3.

Worked example — 995 Hz from 16 kΩ and 10 nF

Use the same resistor and capacitor in both arms: R = 16 kΩ and C = 10 nF. The oscillation frequency is:

f0 = 1 / (2Ï€ × R × C) = 1 / (2Ï€ × 16 × 103 × 10 × 10−9) = 994.7 Hz ≈ 995 Hz

The period is 1 / 995 = 1.01 ms, and at this frequency each capacitor has a reactance of:

XC = 1 / (2Ï€ × 995 × 10 × 10−9) = 16.0 kΩ

Notice that XC equals R at the oscillation frequency — that is no coincidence. At f0 the series arm (R + XC) and the parallel arm (R in parallel with XC) divide the output voltage by exactly 3 with zero phase shift. Below f0 the capacitors look like open circuits and the feedback falls; above f0 they look like short circuits and the feedback falls again. Only at f0 is the feedback strongest, so only that frequency survives and grows into the output sine wave.

Starting up and keeping the sine clean

For the oscillation to start, the gain must be a little more than 3 — a gain of exactly 3 would take forever to build up from noise. In practice the gain is set a touch high (for example R2 = 22 kΩ, giving a gain of 3.2) and something must then pull it back down to 3 once the oscillation is running, or the output will grow until the op-amp clips it into a near-square wave. The classic trick is a small incandescent lamp in series with R1: when cold its resistance is low, so the gain is above 3 and the oscillation starts; as the output grows the lamp warms up, its resistance rises, and the gain falls back to 3, holding the sine at a steady amplitude. Two diodes across part of R2 do the same job more cheaply — they conduct when the output gets large and reduce the effective feedback resistance. With ±12 V supplies the sine reaches about 10 V peak before the op-amp starts to clip.

Designing for another frequency — 10 kHz

Keep C = 10 nF and solve the frequency formula for R:

R = 1 / (2Ï€ × 10,000 × 10 × 10−9) = 1592 Ω ≈ 1.6 kΩ

With R = 1.6 kΩ in both arms the frequency is 1 / (2Ï€ × 1.6 × 103 × 10 × 10−9) = 9947 Hz ≈ 9.9 kHz. The nearest standard value, 1.5 kΩ, gives 10,610 Hz. To tune the frequency, change both resistors together (a dual-gang potentiometer) or both capacitors together (a switched bank); changing only one arm moves the frequency and also spoils the zero phase shift, so the gain of 3 no longer holds and the oscillation may stop.

Key points to remember

  • A Wien bridge oscillator needs a total loop phase shift of 0° and a loop gain of 1: the bridge gives 0° phase shift at f0 and attenuates by 3×, so the non-inverting amplifier must have a gain of exactly 3.
  • Worked example: R = 16 kΩ, C = 10 nF → f0 = 1 / (2Ï€ × R × C) = 995 Hz, period 1.01 ms, Xc = 16 kΩ at f0 (equal to R).
  • The gain is 1 + R2 / R1: R1 = 10 kΩ and R2 = 20 kΩ give exactly 3. Set the gain slightly above 3 to start, then let a lamp or diode limiter pull it back to 3 for a clean sine.
  • With ±12 V supplies the sine reaches about 10 V peak; a gain much above 3 clips it into a near-square wave.
  • Design rule: for 10 kHz with C = 10 nF, R = 1.6 kΩ (f0 = 9947 Hz); 1.5 kΩ gives 10,610 Hz. Tune by changing both arms together.