A 12 V transformer gives you 12 V RMS, which is only about 17 V peak — so how do you get 32 V DC out of it without buying a bigger transformer? The answer is a voltage doubler: two diodes and two capacitors arranged so that each capacitor charges to the peak voltage on alternate half-cycles, and the two charged capacitors stack in series to give roughly twice the peak voltage at the output. It is the same idea behind the high-voltage supply in an old CRT television and the Cockcroft–Walton multipliers used in particle accelerators.
Figure 1: A Delon (full-wave) voltage doubler (a) stacks two half-wave rectifiers — each capacitor charges to the peak voltage, 17 V, so the output is about twice that. The output voltage (b) falls as the load current rises, and bigger capacitors hold it up better.
How the doubler works
The circuit in Figure 1(a) is called a Delon doubler. It is really two half-wave rectifiers sharing one transformer secondary. On the half-cycle when the left side of the secondary goes positive, diode D1 conducts and capacitor C1 charges up to the peak voltage. On the next half-cycle the right side goes positive, diode D2 conducts and capacitor C2 charges to the peak voltage the other way. The two capacitors end up in series across the load, so their voltages add:
Vout (no load) = 2 × Vp − 2 × VF
where Vp is the peak of the secondary voltage and VF ≈ 0.7 V is one silicon diode drop (two diodes are in the charging path). Because each capacitor is recharged once per half-cycle, the ripple frequency is twice the mains frequency — 100 Hz on a 50 Hz supply — which is one advantage over the half-wave version below.
Worked example — 12 V in, about 32 V out
Take a transformer secondary of 12 V RMS at 50 Hz, with C1 = C2 = 1000 µF and a load drawing 100 mA. First the peak voltage:
Vp = 12 × √2 = 16.97 V ≈ 17 V
With no load, the output is:
Vout = 2 × 16.97 − 2 × 0.7 = 33.94 − 1.4 = 32.5 V
Under load the output sags, because each capacitor loses some charge to the load between recharges. The peak-to-peak ripple is the same formula as for a capacitor filter, with the ripple frequency doubled to 100 Hz:
Vripple = I / (f × C) = 0.1 / (100 × 1000 × 10−6) = 1.0 V peak-to-peak
So the average DC output is roughly the no-load voltage minus the ripple:
Vdc ≈ 32.5 − 1.0 = 31.5 V
The load resistance is RL = 31.5 / 0.1 = 315 Ω, and the load power is P = 31.5 × 0.1 = 3.15 W. With smaller capacitors the sag gets worse: with C1 = C2 = 470 µF the ripple doubles to 2.13 V and Vdc falls to about 30.4 V, as Figure 1(b) shows.
How to size the capacitors
Rearrange the ripple formula to design the circuit. Suppose you want the ripple to stay below 0.5 V while the load draws 200 mA:
C ≥ I / (f × Vripple) = 0.2 / (100 × 0.5) = 4000 µF
So choose the next standard size, 4700 µF, for each capacitor. The output would then be about 32.5 − 0.5 = 32.0 V. Two rules of thumb follow from this: double the load current and you must double the capacitance to keep the same ripple, and a doubler always needs larger capacitors than a plain bridge rectifier for the same ripple, because each capacitor supplies the load for a full half-cycle.
The half-wave doubler is worse — use the Delon
There is a simpler doubler, the Villard (half-wave) circuit, with the same two diodes and two capacitors in a different arrangement. It works, but each capacitor is recharged only once per mains cycle, so the ripple frequency is 50 Hz instead of 100 Hz. With the same 1000 µF capacitors and 100 mA load:
Vripple = 0.1 / (50 × 1000 × 10−6) = 2.0 V, Vdc ≈ 32.5 − 2.0 = 30.5 V
Twice the ripple and a volt less output for the same parts — that is why the Delon circuit in Figure 1(a) is the one to build.
Ratings: what the parts must withstand
Each diode sees a peak inverse voltage of twice the peak secondary voltage:
PIV = 2 × Vp = 2 × 16.97 = 33.9 V
A 1N4001 is rated 50 V, which would work, but good practice is to leave a factor of two or more — use a 1N4002 (100 V) or higher. Each capacitor charges to about 17 V, so a 25 V rating is the right choice (never use a 16 V capacitor here — it has no margin). The average diode current is roughly the load current, 100 mA, but the diodes conduct in short pulses at the top of each half-cycle, so the peak current is several times higher; a 1 A diode is comfortable for this design. And remember the limits of the whole idea: the output is not regulated — it falls with load, as Figure 1(b) shows — and the doubler gives no extra isolation. Never connect a doubler directly to the mains without a transformer; the output would be live at mains potential.
Going further: triplers and multipliers
The same stacking trick extends: add one more diode-capacitor stage and you get a tripler, add another and a quadrupler. With the same 12 V secondary the no-load outputs are:
Tripler: 3 × 16.97 − 3 × 0.7 = 48.8 V Quadrupler: 4 × 16.97 − 4 × 0.7 = 65.1 V
Each extra stage adds one more peak voltage minus one more diode drop. This is the Cockcroft–Walton multiplier, and it is how a few volts from a small transformer can be stepped up to thousands of volts for a photomultiplier tube or an electrostatic sprayer — but every stage adds ripple and output resistance, so multipliers are for low-current loads only. For a heavy load, a bigger transformer is always the better answer.
Key points to remember
- A voltage doubler stacks two half-wave rectifiers: each capacitor charges to the peak voltage Vp, and the output is Vout = 2 × Vp − 2 × VF.
- Worked example: a 12 V RMS secondary (Vp = 17 V) gives 32.5 V with no load; with 1000 µF capacitors and a 100 mA load the ripple is 1.0 V peak-to-peak at 100 Hz and Vdc ≈ 31.5 V across a 315 Ω load (3.15 W).
- With 470 µF capacitors the ripple doubles to 2.13 V and the output falls to 30.4 V; to hold ripple to 0.5 V at 200 mA you need C ≥ 4000 µF — use 4700 µF.
- The half-wave (Villard) doubler recharges at 50 Hz, so its ripple is twice as large (2.0 V) and its output a volt lower — build the Delon full-wave doubler instead.
- Ratings: diode PIV = 2 × Vp = 33.9 V, so use a 1N4002 (100 V); each capacitor sees about 17 V, so use a 25 V rating; the average diode current is about the load current.
- The idea extends to triplers (48.8 V) and quadruplers (65.1 V) from the same 12 V secondary, but the output is unregulated, sags with load, and is only for low-current loads — and never run a doubler straight from the mains without a transformer.
