Switch on a transformer — even with nothing connected to its output — and sometimes the breaker trips instantly. The transformer is not faulty. For a few cycles it can draw 10 to 30 times its rated current, a surge called inrush current. The same transformer may switch on quietly a hundred times and then trip once. This article works out how big that surge is, why the exact switch-on moment decides it, how to tame it — and why the same transformer also keeps you safe, by isolating you from the mains.
Why the surge happens — flux, not load
A transformer works on flux: the primary voltage drives a changing magnetic flux in the core, and that flux induces the secondary voltage. The rule is v = N × dΦ/dt — the flux is the integral of the applied voltage. Now suppose you switch on exactly when the mains voltage crosses zero and is rising. The flux then has to rise from zero and, over the first half-cycle, reach twice its normal peak value (the mathematics gives Φ = Φm(1 − cos ωt), which peaks at 2Φm). Worse, the core usually keeps some residual flux from the last time it was switched off — up to Φm in the same direction — so the flux can try to reach 3Φm.
But the core is designed to work at Φm. At 2–3 times that flux it saturates: it cannot carry any more magnetism, its inductance collapses, and the primary becomes little more than a piece of copper wire. The current is then limited only by the winding resistance — and that is why it surges. Switch on instead at the peak of the mains voltage, and the flux starts from zero and rises only to Φm: no saturation, no surge. That is why the same transformer sometimes trips the breaker and sometimes does not — it depends on the exact instant you flip the switch.
Worked example — a 500 VA transformer
Take a 500 VA, 230 V, 50 Hz transformer with 460 primary turns. Its rated primary current is:
Irated = 500 / 230 = 2.17 A
The normal peak flux in the core is:
Φm = V / (4.44 × f × N) = 230 / (4.44 × 50 × 460) = 2.25 mWb
Now the worst case: switch on at a voltage zero-crossing, with residual flux adding to the new flux, so the core saturates hard. The peak mains voltage is 230 × √2 = 325 V, and the only thing limiting the current is resistance — say 2 Ω in the primary winding plus about 3 Ω of mains and lead resistance, 5 Ω in total:
Ipeak = 325 / 5 = 65 A — about 30 times the rated current
The surge does not last. As the DC offset in the flux dies away, each cycle's peak falls — 65 A, then 43.6 A, 29.2 A, 19.6 A, 13.1 A, and about 8.8 A after 0.1 s, as Figure 1(b) shows — and within a few more cycles the current settles to the small steady magnetizing current of roughly 0.15 A peak. Real transformers usually measure 10–30 times rated current on the first peak, exactly in line with this estimate, because the core never saturates perfectly and the source impedance is never zero.
How to tame the inrush
Three fixes are used in practice. First, fit a slow-blow (T) fuse instead of a fast one: a fast fuse sees 65 A and opens, a slow-blow fuse rides through a 0.1 s surge. Second, add an NTC thermistor in series with the primary: cold it is about 10 Ω, so the first peak is only 325 / (10 + 5) = 21.7 A, and then it heats itself up and its resistance falls to about 0.5 Ω, wasting almost nothing in normal running. Third, switch on at the voltage peak — some soft-start circuits do exactly this, closing a relay at the peak of the mains waveform where the flux starts from zero.
The other side of the transformer — isolation that protects you
Look again at Figure 1(a). The primary and secondary windings share the iron core, but there is no wire between them: energy crosses only as magnetism. That means the secondary circuit is electrically floating — it has no connection back to the mains or to earth. Take a 100 VA isolation transformer, 230 V to 12 V: the primary draws 100 / 230 = 0.43 A and the secondary delivers 100 / 12 = 8.33 A, and yet touching one secondary wire cannot shock you, because there is no return path through your body back to earth. The mains side is earthed; the secondary side is not, and the insulation between the windings is hi-pot tested at thousands of volts (1500–3750 V depending on the insulation class).
But do not over-read this protection. Touch both secondary wires and the full secondary voltage drives current through you — at 12 V that is harmless, but an isolation transformer with a 230 V secondary is just as dangerous to touch across its two wires as the mains itself. Isolation removes the earth return path; it does not make the voltage disappear. That is why bench isolation transformers are used with care, and why medical equipment uses specially tested isolation with even stricter leakage limits.
Key points to remember
- Inrush happens because flux is the integral of voltage: switching on at a voltage zero-crossing can push the core flux to 2–3 times its normal peak, the core saturates, and the current is limited only by winding resistance.
- Worked example: a 500 VA, 230 V transformer (rated 2.17 A, Φm = 2.25 mWb) can surge to a worst-case first peak of 65 A — 30 times rated — decaying to about 8.8 A after 0.1 s and then to a magnetizing current of about 0.15 A peak.
- Switching on at the voltage peak avoids saturation, which is why the same transformer sometimes surges and sometimes does not.
- Worked example: a 10 Ω cold NTC thermistor limits the first peak to 21.7 A and then self-heats to about 0.5 Ω; a slow-blow (T) fuse also rides through the 0.1 s surge where a fast fuse would trip.
- An isolation transformer couples the windings only through the core — no wire between them — so touching one secondary wire cannot complete a circuit to earth; a 100 VA, 230 V to 12 V unit delivers 8.33 A on the secondary while its primary draws only 0.43 A.
- Isolation does not make a high-voltage secondary safe to touch across both wires — it only removes the earth return path.
