LC Resonance: Why a Series Circuit Draws Maximum Current and a Parallel Circuit Shows Maximum Impedance

Author: Abloom Instruction Date: November 16, 2026

Connect an inductor and a capacitor to the same AC source and something remarkable happens at one special frequency: the two reactances cancel each other out completely. Below that frequency the capacitor dominates, above it the inductor dominates, but exactly at that frequency the circuit behaves as if only the resistance is there. That frequency is called the resonant frequency, and it is the idea behind every radio tuner, every tuned filter and every wireless charger.

A series RLC circuit with a 5 V source, 10 ohm resistor, 100 microhenry inductor and 100 nanofarad capacitor, beside a plot of series current peaking at 0.5 A at 50.3 kHz and parallel impedance peaking at 1 kilo-ohm at the same frequency


Figure 1: A series RLC circuit (a) draws its largest current at resonance, where XL = XC = 31.6 Ω. The curves (b) show the series current peaking at 0.5 A and the parallel impedance peaking at 1 kΩ, both at the same resonant frequency, f0 = 50.3 kHz.

Why resonance happens

Inductive reactance grows with frequency, capacitive reactance falls with frequency:

XL = 2Ï€fL      XC = 1 / (2Ï€fC)

At low frequencies XC is huge and XL is tiny, so the capacitor rules the circuit. At high frequencies it is the other way round. Somewhere in between they must be equal — and that crossing point is the resonant frequency. Setting XL = XC and solving for f gives the most-used formula in tuned circuits:

f0 = 1 / (2Ï€√(LC))

At f0 the net reactance is zero (XL − XC = 0), so the impedance of a series circuit is just its resistance, Z = R, and the current is at its maximum. The reactances at resonance are equal to the characteristic impedance:

Z0 = √(L / C) = XL = XC at f0

Worked example — a series RLC circuit

Take L = 100 µH and C = 100 nF in series with R = 10 Ω, driven by a 5 V RMS source. First the resonant frequency:

f0 = 1 / (2Ï€√(100 × 10−6 × 100 × 10−9)) = 1 / (2Ï€ × 3.16 × 10−6) = 50,329 Hz ≈ 50.3 kHz

At that frequency the reactances are:

XL = XC = 2Ï€ × 50,329 × 100 × 10−6 = 31.6 Ω

They cancel, so Z = R = 10 Ω and the current is simply:

I = V / R = 5 / 10 = 0.5 A

Now the surprise: the voltage across the inductor and across the capacitor are each much larger than the 5 V supply:

VL = VC = I × 31.6 = 0.5 × 31.6 = 15.8 V

That is not a mistake — the two 15.8 V drops are 180° out of phase, so they cancel and leave only the 5 V across the resistor. The magnification factor is the Q factor:

Q = XL / R = 31.6 / 10 = 3.16    and    VL = VC = Q × V = 3.16 × 5 = 15.8 V

The power is all dissipated in the resistor: P = V² / R = 25 / 10 = 2.5 W. The inductor and capacitor only swap energy back and forth — the inductor's magnetic field feeds the capacitor's electric field and back again, 50,329 times a second.

Bandwidth: how sharp is the peak?

The current stays high only near f0. The bandwidth is the frequency range between the two half-power points, where the current has fallen to 0.707 of its peak value:

BW = f0 / Q = 50.33 / 3.16 = 15.9 kHz

So the half-power frequencies are f1 ≈ 43.0 kHz and f2 ≈ 58.9 kHz (f2 − f1 = 15.9 kHz, as expected). At both of them the current is 0.5 / √2 = 0.354 A and the power is half: 1.25 W. A higher Q means a narrower, sharper peak — good for selecting one radio station and rejecting the next one. Away from resonance the current collapses: at 10 kHz the net reactance is −152.9 Ω (capacitive), Z = 153 Ω and I = 32.6 mA; at 200 kHz the net reactance is +117.7 Ω (inductive), Z = 118 Ω and I = 42.3 mA. The circuit passes 50 kHz and almost ignores everything else — that is what a filter does.

The parallel circuit does the opposite

Put the same L and C in parallel with a 1 kΩ resistor across the 5 V source. At f0 the inductor and capacitor currents are equal and opposite, so they cancel at the source terminals and the impedance is at its maximum, Z = Rp = 1 kΩ, as Figure 1(b) shows. The Q factor is now:

Qp = Rp / Z0 = 1000 / 31.6 = 31.6

so the bandwidth is much narrower: BW = 50.33 / 31.6 = 1.59 kHz. The source only supplies 5 mA (5 V / 1 kΩ), but a much larger current circulates between L and C:

Icirculating = V / Z0 = 5 / 31.6 = 158 mA

— 31.6 times the supply current. That is the practical warning with parallel resonance: the wires and components in the LC loop can carry far more current than the supply ever delivers, so they must be rated for it.

A real use: tuning an AM radio

An AM radio tunes stations from 530 kHz to 1600 kHz with a parallel LC circuit and a variable capacitor. With a fixed inductor of L = 220 µH, the capacitor needed is C = 1 / ((2Ï€f)² × L):

At 530 kHz: C = 1 / ((2Ï€ × 530,000)² × 220 × 10−6) = 410 pF

At 1600 kHz: C = 1 / ((2Ï€ × 1,600,000)² × 220 × 10−6) = 45 pF

So a variable capacitor that swings from about 45 pF to 410 pF tunes the whole AM band — one station at a time, because the high-Q parallel circuit rejects the stations on either side. Turn the dial and you are really just changing C and moving f0.

Key points to remember

  • Resonance is where XL = XC: f0 = 1 / (2Ï€√(LC)). Below f0 the circuit is capacitive, above f0 it is inductive.
  • Worked example: L = 100 µH, C = 100 nF → f0 = 50.3 kHz, XL = XC = 31.6 Ω; with R = 10 Ω and 5 V, the series current peaks at 0.5 A and VL = VC = 15.8 V.
  • Q = XL / R = 3.16 for the series circuit; bandwidth BW = f0 / Q = 15.9 kHz, between 43.0 kHz and 58.9 kHz, where the current is 0.354 A and the power is halved.
  • Off resonance the current collapses: 32.6 mA at 10 kHz and 42.3 mA at 200 kHz — the circuit selects one frequency and rejects the rest.
  • In parallel, impedance peaks at f0: with Rp = 1 kΩ, Q = 31.6, BW = 1.59 kHz, the supply gives only 5 mA while 158 mA circulates between L and C — rate the loop components for the circulating current, not the supply current.
  • Real use: an AM tuner with L = 220 µH needs C = 410 pF at 530 kHz and 45 pF at 1600 kHz — one variable capacitor covers the whole band.