Inverting Summing Amplifier: Mix Three Signals with One Op-Amp

Author: Abloom Instruction Date: November 18, 2026

A mixing desk takes a microphone, a guitar and a keyboard and adds them into one signal. The circuit that does the adding is the inverting summing amplifier: one op-amp, one resistor per input, and one feedback resistor. Each input gets its own gain, and — unlike a passive resistor mixer — turning one input up or down does not change the others at all. This article works out a three-input mixer with real numbers.

Schematic of an inverting summing amplifier with three inputs of 0.5, 2.0 and 0.25 volts through 10, 20 and 5 kilo-ohm resistors into the inverting input of an op-amp with a 10 kilo-ohm feedback resistor giving minus 2.0 volts out, beside a plot of output voltage against the first input, a straight line of slope minus 1 passing through the design point

Figure 1: A three-input summing amplifier (a) — the three input resistors set the gains to −1, −0.5 and −2, and the output is the sum of the three scaled inputs. The output against V1 (b) is a straight line of slope −1, with V2 and V3 fixing the offset at −1.5 V. (Schematic, not to scale.)

Why the inputs do not interact — the virtual earth

The key is the op-amp's inverting (−) input. With negative feedback the op-amp holds its two inputs at the same voltage, and the (+) input is tied to ground through R4 — so the (−) input sits at 0 V even though no wire connects it to ground. That point is called a virtual earth. Each input resistor therefore has its full input voltage across it, and the current through it depends only on its own input:

I = V / R  (because the far end of the resistor is at 0 V)

No current flows into the op-amp input itself, so all three input currents must flow through the feedback resistor RF. The voltage drop they make across RF is the output — and because every current is independent, each input contributes its own term and nothing else. That is why a passive mixer (resistors only) loads its sources and lets them talk to each other, while the summing amplifier keeps them separate.

Worked example — three inputs, one output of −2.0 V

Take RF = 10 kΩ and three inputs: a microphone at V1 = 0.5 V through R1 = 10 kΩ, a guitar at V2 = 2.0 V through R2 = 20 kΩ, and a keyboard at V3 = 0.25 V through R3 = 5 kΩ. Each input has its own gain, −RF / R:

Gain 1 = −10 / 10 = −1   |   Gain 2 = −10 / 20 = −0.5   |   Gain 3 = −10 / 5 = −2

The output is the sum of the three scaled inputs:

Vout = −(1 × 0.5 + 0.5 × 2.0 + 2 × 0.25) = −(0.5 + 1.0 + 0.5) = −2.0 V

Check it by currents. Each input drives its current into the virtual earth:

I1 = 0.5 / 10 kΩ = 50 µA   |   I2 = 2.0 / 20 kΩ = 100 µA   |   I3 = 0.25 / 5 kΩ = 50 µA

The three currents add at the summing node and all 200 µA flows through RF:

Vout = −200 µA × 10 kΩ = −2.0 V  — the same answer, as it must be.

What each input contributes

Because the inputs are independent, you can read off what each one does on its own:

V1 only (0.5 V): Vout = −0.5 V  |  V2 only (2.0 V): Vout = −1.0 V  |  V3 only (0.25 V): Vout = −0.5 V

Hold V2 and V3 fixed and sweep V1, and the output follows a straight line, Vout = −V1 − 1.5 V — the −1.5 V is the fixed contribution of V2 (−1.0 V) and V3 (−0.5 V), and the slope of −1 is V1's gain, exactly as Figure 1(b) shows. The minus sign is the price of the inverting configuration: the output is the inverted sum. If the polarity matters, follow it with a second inverting stage (gain −1) or use the non-inverting summing circuit instead — but that version needs matched resistors and has a gain that depends on all of them at once.

R4, offsets and the clipping limit

R4, from the (+) input to ground, is there to cancel the offset caused by the op-amp's input bias current. The (−) input sees RF in parallel with the three input resistors, so R4 is chosen to match that resistance:

R4 = 10 kΩ ‖ 20 kΩ ‖ 5 kΩ ‖ 10 kΩ = 1 / (0.1 + 0.05 + 0.2 + 0.1) mS = 2.22 kΩ → use 2.2 kΩ

With both inputs seeing the same resistance, the bias-current voltage drops cancel to first order. Finally, check the output against the supplies. With ±12 V supplies a typical op-amp swings to about ±10 V, and −2.0 V is comfortably inside that. Even with all three inputs at their largest — V1 = 2 V, V2 = 2 V, V3 = 1 V — the output is −(2 + 1 + 2) = −5 V, still fine. Only if the summed inputs tried to push the output past about ±10 V would the top of the waveform clip flat — so a mixer that must stay clean needs headroom for the loudest moment of all its inputs together, not just one at a time. Each source also sees its own input resistor as its load (10 kΩ, 20 kΩ and 5 kΩ here), so a source with a high output resistance would lose some signal in a divider with its input resistor — use a buffer in front of it if that matters.

Key points to remember

  • The inverting summing amplifier adds scaled inputs at a virtual-earth node: Vout = −RF × (V1/R1 + V2/R2 + V3/R3), so each input has its own gain −RF/R and the inputs do not interact.
  • Worked example: RF = 10 kΩ, R1 = 10 kΩ, R2 = 20 kΩ, R3 = 5 kΩ, V1 = 0.5 V, V2 = 2.0 V, V3 = 0.25 V → gains −1, −0.5, −2; currents 50, 100, 50 µA; total 200 µA through RF; Vout = −2.0 V.
  • Each input alone: V1 gives −0.5 V, V2 gives −1.0 V, V3 gives −0.5 V; with V2 and V3 fixed, Vout = −V1 − 1.5 V, a straight line of slope −1.
  • R4 cancels the bias-current offset: R4 = R1 ‖ R2 ‖ R3 ‖ RF = 2.22 kΩ → use 2.2 kΩ.
  • Output limit: ±12 V supplies swing to about ±10 V; the −2.0 V output is well inside, and even the loudest combined inputs (−5 V) stay clean — size the headroom for all inputs together.