Diode Clipping and Clamping Circuits: Shape a Waveform with One Diode and a Capacitor

Author: Abloom Instruction Date: November 14, 2026

A diode conducts in one direction only — and that single property lets you reshape a waveform almost any way you like. A clipper cuts off the part of a waveform above (or below) a chosen level, while a clamper shifts the whole waveform up or down without changing its shape. Both circuits use just one diode, and the clamper adds one capacitor. They show up everywhere: clippers protect inputs from overvoltage, clampers restore the DC level of a video signal, and both appear in audio distortion and signal-conditioning circuits.

Series diode clipper circuit with a 2 volt bias battery and a negative clamper circuit with a 1 microfarad capacitor, beside a plot of a 10 volt sine wave clipped flat at plus 2.7 volts and clamped to swing between minus 0.7 and minus 20.7 volts


Figure 1: The clipper (a) and the clamper (b), and what each does to the same 10 V sine wave (c). The clipper cuts the top off; the clamper moves the whole wave down. (Schematic, not to scale.)

The clipper — cutting the top off a sine wave

In the series clipper of Figure 1(a), the diode, a 2 V bias battery and the load resistor are all in series. The diode conducts only when the input is high enough to overcome both the battery and the diode's own forward drop. A silicon diode drops about 0.7 V, so the clipping level is:

Vclip = VB + VF = 2.0 + 0.7 = 2.7 V

While the input is below 2.7 V the diode is off, no current flows, and the output simply follows the input. While the input is above 2.7 V the diode conducts and the output is held at 2.7 V — the top of the sine is cut flat, as in Figure 1(c). The negative half-cycle is untouched: the diode is reverse-biased there, so the full −10 V peak passes through.

Worked example — how much of the cycle is clipped?

Feed in a 10 V peak sine at 1 kHz. Clipping starts when the rising sine reaches 2.7 V:

sin θ = 2.7 / 10 = 0.27  →  θ = 15.7°

The sine stays above 2.7 V until the mirror-image angle, 180° − 15.7° = 164.3°. So the output is flat at 2.7 V for:

164.3° − 15.7° = 148.7° of each 360° cycle

That is more than 40% of the cycle spent clipped — which is why a clipper visibly flattens a waveform even with a small bias. Without the battery at all, the same circuit clips at just the diode drop, +0.7 V. To clip at a different level, choose the battery: for a +5 V clipping level, VB = 5 − 0.7 = 4.3 V. Reverse the battery and the diode, and the circuit clips the negative peak instead.

The clamper — shifting the whole wave down

The clamper of Figure 1(b) puts a capacitor in series with the signal and a diode from the output node to ground. On the first positive peak the diode conducts briefly and charges the capacitor to:

VC = Vp + VF = 10 + 0.7 = 10.7 V

After that the diode stays off, the capacitor holds its charge, and the output is simply the input minus the capacitor voltage:

vout = vin − 10.7 V

So the output swings from −0.7 V (when the input is at +10 V) to −20.7 V (when the input is at −10 V). The sine keeps its exact shape and its 20 V peak-to-peak size — it has just been pushed down so that its positive peak sits at zero. That is the clamper's job: it restores or sets the DC level of a waveform. Reverse the diode and the wave is pushed up instead, swinging from +0.7 V to +20.7 V.

Worked example — does the capacitor hold its charge?

The capacitor only stays charged if it cannot discharge much between peaks. Its discharge path is the load resistor, so the time constant is:

Ï„ = R × C = 100 kΩ × 1 µF = 100 ms

At 1 kHz the period is 1 ms, so Ï„ is 100 times the period — the capacitor loses only about:

Droop ≈ 20 V × T / Ï„ = 20 × 1 / 100 = 0.2 V per cycle

That 0.2 V tilt on a 20 V wave is barely noticeable. The rule is simple: make RC at least 100 times the period and the clamper holds its level. At a low frequency such as 50 Hz (20 ms period), the same 100 ms time constant is only 5 times the period, and the droop would grow to about 4 V — you would need a bigger capacitor, for example 10 µF with the same 100 kΩ resistor.

Key points to remember

  • A clipper cuts off the part of a waveform above a chosen level; a clamper shifts the whole waveform up or down without changing its shape.
  • Worked example: a 10 V peak sine through a series clipper with a 2 V battery and a silicon diode (0.7 V) is clipped at +2.7 V; clipping starts at 15.7° and ends at 164.3°, so the output is flat for 148.7° of each cycle, while the −10 V negative peak passes untouched.
  • To clip at +5 V, use a 4.3 V battery (5 − 0.7); with no battery the same circuit clips at +0.7 V.
  • Worked example: a negative clamper with C = 1 µF and R = 100 kΩ charges the capacitor to 10.7 V, so the output swings from −0.7 V to −20.7 V — the 20 V peak-to-peak sine keeps its shape, just shifted down.
  • For a good clamper, make RC at least 100 times the signal period: here 100 ms against a 1 ms period gives only 0.2 V of droop per cycle.
  • Clippers protect inputs from overvoltage; clampers restore the DC level of a signal — for example the sync pulses of a video waveform.