Capacitor ESR and Ripple Current: Why Two 2200 µF Capacitors Behave Very Differently

Author: Abloom Instruction Date: November 15, 2026

Two capacitors can both be labelled 2200 µF and 25 V, yet one runs cool in a power supply while the other runs hot, adds ripple to the output and dies young. The difference is ESR — the equivalent series resistance hidden inside every real capacitor. This article works out what ESR does to ripple voltage, how much heat it makes, and how to pick a capacitor whose ripple-current rating actually fits the job.

Equivalent circuit of a real capacitor as an ideal capacitor in series with its ESR, beside a plot of the output ripple voltage showing the slow capacitive sawtooth with sharp ESR steps at each charge pulse

Figure 1: A real capacitor (a) is an ideal capacitor in series with its ESR, and the ripple waveform (b) shows the ESR as a sharp step on top of the slow capacitive sawtooth. (Schematic, not to scale.)

What ESR is — a resistor you cannot remove

A real electrolytic capacitor is not a pure capacitance. Its foil, electrolyte and leads all have resistance, and the standard model puts them together as one resistor — the ESR — in series with an ideal capacitor, as in Figure 1(a). At 100 Hz a general-purpose 2200 µF capacitor has an ESR of roughly 0.15 Ω. That sounds negligible, until you remember that the ripple current in a power supply is large and flows through that resistor on every cycle.

Worked example — the two parts of the ripple voltage

Take the bridge-rectifier filter from an earlier article: a 2200 µF capacitor feeding a 0.5 A load, with full-wave ripple at 100 Hz. The ripple has two parts. The capacitive part is the familiar sawtooth — the capacitor discharges into the load between charging pulses:

ΔVcap = I / (f × C) = 0.5 / (100 × 2200 µF) = 2.27 V peak-to-peak

The ESR part is different: the charging pulses from the rectifier are short and tall — about 3 A peak for a 0.5 A load — and each pulse drops a voltage across the ESR:

ΔVESR = Ipeak × ESR = 3 × 0.15 = 0.45 V

So the total ripple is not just the 2.27 V sawtooth: every charging pulse adds a sharp 0.45 V step on top of it, as Figure 1(b) shows. In an audio amplifier or a sensitive analogue circuit, those sharp steps are far more troublesome than the slow sawtooth — they are high-frequency noise that a later regulator cannot easily remove.

Worked example — the heat inside the capacitor

The same ripple current heats the ESR, and the heating depends on the rms current, not the average. In this circuit the capacitor ripple current is about 0.9 A rms — roughly twice the load current, because the charging pulses are short and tall. The power lost in the ESR is:

P = I² × ESR = 0.9² × 0.15 = 0.12 W

0.12 W inside a small aluminium can raises its core temperature by about 3.6 °C (a typical can has a thermal resistance near 30 °C/W). That matters because an electrolytic capacitor's life roughly halves for every 10 °C rise in core temperature: a capacitor rated for 2000 hours at 105 °C lasts far longer at 85 °C, but a hot-running one ages fast. Most capacitor failures in old power supplies are dried-out electrolyte caused by exactly this self-heating.

Worked example — general-purpose vs low-ESR

Compare two 2200 µF capacitors carrying the same 0.9 A rms ripple current. A general-purpose part with ESR 0.30 Ω loses:

P = 0.9² × 0.30 = 0.24 W, core rise ≈ 7.3 °C, ESR ripple = 0.27 V

A low-ESR part with ESR 0.05 Ω loses:

P = 0.9² × 0.05 = 0.04 W, core rise ≈ 1.2 °C, ESR ripple = 0.045 V

Same capacitance, same voltage rating — but the low-ESR capacitor runs six times cooler and adds six times less ripple. That is why switching power supplies and motherboards specify low-ESR capacitors: in those circuits the ripple current is large and the frequency is high, so ESR dominates everything.

How to choose — read the ripple-current rating

Every electrolytic capacitor datasheet lists a ripple-current rating, usually at 105 °C and 100 kHz (or 120 Hz). The rule is simple: the capacitor's rated ripple current must be larger than the actual ripple current in your circuit, with margin. In our example the circuit needs 0.9 A rms, so pick a capacitor rated for at least 1.2 A. If the rating is too low, the capacitor will overheat and dry out — and the first symptom is usually a power supply that hums, a bulging capacitor top, or a circuit that resets under load. Two more practical rules: ESR rises as the capacitor gets cold and as it ages, so leave margin for both; and in a high-frequency switching supply, check the ESR at the switching frequency, not at 100 Hz, because ESR falls with frequency for some types and the datasheet number is what counts.

Key points to remember

  • A real capacitor is an ideal capacitor in series with its ESR — the resistance of its foil, electrolyte and leads.
  • Worked example: in a 2200 µF bridge filter feeding 0.5 A, the ripple is 2.27 V peak-to-peak from the capacitance plus a sharp 0.45 V step from the ESR (3 A peak charging pulses × 0.15 Ω).
  • Worked example: a ripple current of 0.9 A rms through 0.15 Ω loses 0.12 W and raises the capacitor core by about 3.6 °C; capacitor life roughly halves for every 10 °C rise.
  • Worked example: at the same 0.9 A ripple current, a general-purpose capacitor (ESR 0.30 Ω) loses 0.24 W and adds 0.27 V of ripple, while a low-ESR part (0.05 Ω) loses only 0.04 W and adds 0.045 V.
  • Always choose a capacitor whose datasheet ripple-current rating exceeds the actual ripple current in your circuit, with margin — and remember ESR rises when cold and with age.
  • If a power supply hums, bulges or resets under load, check the filter capacitors' ESR first: a capacitance meter can read fine while the ESR is ten times its original value.